The article down below in relation to Tools You Need to Install a New Bathtub is extremely fascinating. Don't miss out on it.
Mounting a bathtub isn't specifically rocket science, however it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old tub with a new one is also a moderately tough task. If the old bathtub is readily easily accessible, the job can relocate easily; if you need to open a wall to remove the old bathtub as well as place the new bathtub, the task is much harder. In either instance, the task is within a home handyman's skills, although you will certainly require a helper to move out the old bathtub as well as embeded in the new one. Ensure you have certified yourself for the task as well as are comfortable trying it. Rather than working with a contractor to take over a halfway-completed project, it is better to take into consideration using one before you start. Chances are you may require a professional plumber to make tube connections.
This post will certainly aid you mount a brand-new bath tub in your restroom if you have actually already bought a brand-new bathtub and also do not need to change the setup of your previous water pipelines.
Your tools as well as product list should comprise the following:
Planning for the Installation
First of all, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to prevent pressure on the bath tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you must do is disconnect the water supply. After doing so, turn on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome due to the restricted gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning during this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Using both wooden boards under its feet, put the tub in the needed position. The wood boards are handy in evenly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and readjusting the feet on the bathtub up until the level reviews degree.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the suitable supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Turn on the water supply as well as examine all joints as well as brand-new pipework for leakages and also tighten them if essential. Fill up the bath tub and likewise examine the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bath tub should wait up until the bathtub has been used a minimum of when as this will resolve it right into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will need a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washers remain in place in between the tap and the sink. Protect the tap in position with the maker provided backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former type needs to be linked to the tap finishes first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a rigid seal, triggering the water to pass through the wall between the bathroom as well as the tiling, causing problems with moisture and feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of soaked paper or soft rope. Remember to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the tub is in usage. The sealer can crack relatively early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly offered on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or waterproof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you enjoyed reading our excerpt about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you for spending some time to browse our article post. Enjoyed our write up? Please share it. Help another person discover it. Thanks a bunch for your time. Visit us again soon.
Expertise? One call away.